BP1440S-40
TAT
BP1440S-40
| Style: | |
|---|---|
| Operating Voltage: | |
| Rated Current: | |
| Sound Output at 10cm: | |
| Resonant Frequency: | |
| Capacitance: | |
| Availability: | |
| Quantity: | |
True SMD Package for Pick-and-Place — side metallized pads (15.9 mm total width) mate with standard SMT feeders; drop into reflow with no hand insertion or wave soldering.
85 dB High SPL at 5 Vp-p — louder than typical 11×9 mm SMD buzzers (≈75 dB); clearly audible indoors and inside enclosures.
Wide Drive 1–20 Vp-p, Only 3 mA — from a 1 V coin cell to 20 V industrial rails; capacitive piezo draws near-zero DC current for battery-powered designs.
4 kHz Resonant, MCU-Programmable Pitch — sweep frequency in firmware for chimes and multi-tone alarms instead of a fixed beep.
Black PPS Housing, Reflow Proof — polyphenylene sulfide resin withstands lead-free reflow peaks without delamination, blistering or warping.
Wide Temperature -30 °C ~ +70 °C — suits outdoor, automotive and cold-climate products beyond standard consumer ratings (0 °C to +50 °C).
Ultra-Thin 3.2 mm, 0.5 g — fits slim PCBs and compact enclosures; near-weightless for wearables and IoT nodes.
RoHS Compliant; tape & reel for high-volume SMT assembly.
Parameter | Specification |
|---|---|
Brand | TAT |
Model | BP1440S-40 |
Buzzer Type | SMD Passive Piezoelectric Ceramic Buzzer (external square-wave drive) |
Resonant Frequency | 4000 ± 500 Hz |
Operating Voltage | 1 – 20 Vp-p |
Rated Current | ≤ 3 mA at 4 kHz, 50% duty square wave, 5 Vp-p |
Sound Output (SPL) | ≥ 85 dB at 10 cm, at 4 kHz 50% duty, 5 Vp-p |
Capacitance | 15000 ± 30% pF at 1 kHz |
Body Dimensions | 14.0 * 14.0 * 4.0 mm |
Total Width (incl. side pads) | 16.0 * 14.0 mm |
Mounting | SMD side metallized pads, reflow solderable |
Pad Thickness | 0.2 mm |
Sound Port | Center hole on top face |
Housing Material | Black PPS (heat-resistant) |
Net Weight | Approx. 0.5 g |
Operating Temperature | -30 °C ~ +70 °C |
Storage Temperature | -40 °C ~ +85 °C |
Tolerance | ±0.3 mm unless specified |
Certification | RoHS Compliant |
Origin | China |
Networking & Telecom — router fault alarms, switch status beepers, optical-network terminals, server rack alerts
Industrial — PLC panel beepers, temperature controllers, power-supply alarms, instrumentation
Medical Portable — glucose meters, blood pressure monitors, pulse oximeters, portable diagnostics
Smart Home — smart locks, doorbells, touch panels, smoke detectors, gas alarms
Low-Power IoT — battery sensor nodes, asset trackers, smart meters, beacon tags
Automotive Aftermarket — OBD dongles, dashcams, parking-sensor buzzers
Office Equipment — printer/copier error signals, scanner status alarms
Loudest SMD Buzzer in Its Class — 85 dB at 5 Vp-p reaches inside closed enclosures where smaller 75 dB SMD buzzers go unnoticed.
SMT-First Design — PPS housing and side pads pass lead-free reflow; no through-hole labor, no wave-solder fixture.
One Buzzer for Every Voltage — 1 to 20 Vp-p range eliminates SKU proliferation across battery, 5 V and 12/24 V products.
Micro-Power 3 mA — capacitive draw lets battery sensors alert for years on a single cell.
Full OEM/ODM Flexibility — alternate frequencies (2/4/8 kHz), pad layout, wire-lead or connector versions available.
Q1: Active or passive? Passive SMD piezo. Drive it with a square wave at 4000 Hz (≈50% duty) from an MCU PWM pin; DC voltage alone produces no sound.
Q2: Can it survive reflow soldering? Yes. The black PPS housing is rated for lead-free reflow peaks; follow the JEDEC J-STD-020 curve in the datasheet.
Q3: How do I drive it from an MCU? Connect one SMD pad to a GPIO PWM output (4 kHz square wave) and the other to GND. For 12–20 Vp-p drive, use an NPN/MOSFET or half-bridge stage with a current-limiting resistor.
Q4: How loud is 85 dB in an enclosure? At 5 Vp-p measured 10 cm away, 85 dB is a clear indoor alert; when enclosed, route the sound port through a housing outlet hole to retain output.
Q5: Do you supply tape & reel? Yes. Volume orders ship tape & reel, ESD-shielded and moisture-bagged for SMT feeders.
Q6: Can I get a wire-lead version? Yes. Standard is SMD pads; wire-lead and JST connector variants are available on request.