Home » Products » Buzzer » SMD Buzzer » TAT BMC9650S-0527 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2700Hz
TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz
TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz
TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz
TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz
TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz TAT BMC9650S-0524 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2400Hz

loading

TAT BMC9650S-0527 Magnetic Buzzer Pin Mount 9.6*5.0mm 4-7VDC 2700Hz

Share to:
facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button
TAT BMC9650S-0527 is a surface-mount active electromagnetic buzzer with a built-in oscillator. Solder it down and apply 5VDC — it sounds immediately, no PWM, no driver transistor. In a 9.6*9.6*5.0mm square package of heat-resistant black LCP, it delivers ≥85 dB continuous tone at only 30mA. Its -20 °C to +80 °C operating range makes it a fit for indoor equipment and enclosed outdoor enclosures.
  • BMC9650S-0527

  • TAT

  • BMC9650S-0527

Style:
Rated Voltage:
Operating Voltage:
Rated Current:
Sound Output at 10cm:
Resonant Frequency:
Tone:
Availability:
Quantity:

Key Features

  • Built-In Oscillator — SMD, DC Power, Instant Sound — reflow onto the board, feed 5 V DC, and it beeps continuously; no firmware or external drive.

  • Wide Temperature Range -20 °C ~ +80 °C — covers cold rooms, warm cabinets and vehicle interiors; storage -30 °C ~ +85 °C.

  • Standard 9.6*9.6 mm SMD Package — common square footprint for automatic pick-and-place feeders.

  • ≥85 dB Continuous Tone at 5 V — clearly audible alarm/status beep in panels and equipment.

  • Only 30 mA — low-current drive from standard 5 V logic rails.

  • 2700 Hz Warm Magnetic Tone — clear, non-harsh alert sound.

  • Black LCP Housing, Reflow-Compatible — heat-resistant LCP and side sound port; 0.7 g.

  • RoHS Compliant.

Technical Specifications

Parameter

Specification

Brand

TAT

Model

BMC9650S-0527

Buzzer Type

SMD Active Electromagnetic Buzzer (built-in oscillator)

Rated Voltage

5 VDC

Operating Voltage

4 – 7 VDC

Rated Current

≤ 30 mA at 5 VDC

Sound Output (SPL)

≥ 85 dB at 10 cm, at 5 VDC

Resonant Frequency

2700 ± 300 Hz

Tone

Continuous

Body Size

9.6*9.6*5.0 mm

Sound Port

Side-facing

Mounting

SMD soldering pads, 2 ± 0.1 mm; stand-off 0.15 ± 0.05 mm

Polarity

(+) / (−) marked

Housing Material

Black LCP (reflow-compatible)

Net Weight

Approx. 0.7 g

Operating Temperature

-20 °C ~ +80 °C

Storage Temperature

-30 °C ~ +85 °C

Tolerance

±0.3 mm except specified

Certification

RoHS Compliant

Origin

China

image.png

Downloads

Datasheet: TAT BMC9650S-0527 Datasheet (PDF, 5 pages, 365 KB)

The document contains the full technical parameters, the dimensional drawing, the electrical and acoustical measuring condition, the reliability test conditions, the recommended reflow profile with soldering pattern, and the packing specification.

Measurement Conditions

The part is measured under 5 - 35 °C, 45 - 85 % R.H., 860 - 1060 hPa. Where a value needs a tighter reference, the standard condition 25 ±3 °C, 60 ±10 % R.H., 860 - 1060 hPa is used instead. Every value in the limit table below states the condition it was taken under.

Sound pressure is measured on the axis at 10 cm from the sound port, driving the part at its rated 5 VDC. Because this model carries a built-in oscillator, a DC supply is enough — no external square wave is needed.

Electrical & Acoustic Limits

Read the table as a window, not a single number: a part is accepted anywhere inside the Min - Max range. Design your alarm threshold against the Min column, not the typical value, so that every unit in the lot clears your audibility requirement.

Parameter

Test Condition

Min

Typ

Max

Unit

Rated Voltage

DC supply

—

5

—

VDC

Operating Voltage

DC supply

4

—

7

VDC

Rated Current

at 5 VDC

—

—

30

mA

Sound Output

5 VDC, 10 cm, on axis

85

—

—

dB

Resonant Frequency

—

2400

2700

3000

Hz

Weight

—

—

0.7

—

g

Reliability Test

After any of the tests below the part shall meet specification without any degradation in appearance and performance other than SPL, and SPL shall not deviate more than -10 dB from the initial value.

Test Item

Test Condition

Acceptance Criteria

Ordinary Temperature Life

96 h at 25 ±10 °C, rated voltage, resonant frequency, 1/2 duty square wave

SPL change ≤ 10 dB

High Temperature Storage

+85 °C for 96 h, then 2 h at normal condition

No visible damage

Low Temperature Storage

-30 °C for 96 h, then 2 h at normal condition

No visible damage

Humidity

+40 ±3 °C, 90 - 95 % R.H. for 48 h, then 6 h at room temperature

No visible damage

Temperature Shock

70 °C / 1 h → 25 °C / 3 h → -30 °C / 1 h → 25 °C / 3 h, 10 cycles total

No visible damage

Drop Test

Standard packaging dropped from 75 cm onto 5 cm hard board, 3 sides, 6 faces

No visible damage

Vibration

1000 cycles/min, amplitude 1.5 mm, 1 h on each of 3 axes

No visible damage

Soldering Condition

Two process limits matter more than the profile itself: too high a soldering temperature, and too steep a temperature gradient (rapid heating or cooling), are the two documented causes of electrical failure and mechanical damage on this part. Keep bending, expanding and pulling forces, and any shock against the body, to a minimum during automated mounting.

Process Step

Recommended Parameter

Pre-heating

170 - 190 °C

Soak temperature

180 ±10 °C

Pre-heat time

90 ±30 sec

Ramp up / down rate

4 °C/sec max.

Peak temperature

250 °C max.

Time at peak

10 sec max.

Cooling

Cooling by air

Mounting & PCB Notes

  • PCB footprint — two soldering pads 1.9 mm wide, 6.8 mm pad-to-pad gap, 10.6 mm outer span. Pad height and its tolerance are given on the approval drawing.

  • Part terminals — 2 ±0.1 mm wide with a stand-off of 0.15 ±0.05 mm. Body tolerance ±0.3 mm except where specified, housing in black LCP, reflow compatible.

  • Acoustic path — the sound port faces the side of the housing. When the part sits against a panel or a gasket, leave that opening unobstructed; a blocked port costs several dB and is often mistaken for a weak unit.

  • Foreign material is the most common field failure cause. The part is not sealed against ingress, so keep magnetic powder, washing solvent, flux residue and corrosive gas out of the housing during your production process — contamination inside the cavity reduces sound output and can silence the part.

Typical Applications

  • Industrial Control — PLC fault alarms, VFD beepers, control-cabinet alerts

  • Security — door access, smoke detectors, smart locks, alarm panels

  • Telecom & Network — routers, switches, ONT alert beepers

  • Medical — patient monitors, portable diagnostic equipment

  • Office Equipment — printers, scanners, projector warnings

Why Choose TAT BMC9650S-0527?

  1. SMD + Active = Simplest Loud Beep — reflow it, wire 5 V, done; no drive design.

  2. Wide Temperature Coverage — -20 °C to +80 °C covers cold rooms, warm cabinets and vehicle interiors.

  3. Built for Automated Lines — LCP housing and standard square pads pass reflow; tape & reel.

  4. 85 dB Where It Matters — clearly audible in panels and equipment rooms.

  5. OEM Flexibility — intermittent tone, alternate frequencies and custom reel quantities available.

Frequently Asked Questions

Q1: Active or passive? Active. It has a built-in oscillator circuit. Apply DC voltage (4–7 V) and it sounds — no PWM needed.

Q2: Is it SMD or through-hole? SMD. It has surface-mount pads on the bottom and reflow-compatible black LCP housing; ship tape & reel.

Q3: How do I connect it? Solder the two SMD pads to your 5 V supply (plus/minus). Use a switch, transistor or GPIO to turn it on/off.

Q4: What is the temperature range? -20 °C to +80 °C operating, storage -30 °C to +85 °C — covers most indoor equipment and enclosed outdoor enclosures.

Q5: How loud is 85 dB? At 5 V measured 10 cm away, 85 dB is a clear indoor alert — typical for panels and instruments.

Q6: Can it survive reflow? Yes. The black LCP housing is rated for lead-free reflow; follow the JEDEC J-STD-020 curve in the datasheet.

Previous: 
Next: 

RELATED PRODUCTS

WhatsApp

Call Us

+86-131-3888-7759

QUICK LINKS

PRODUCT CATEGORY

SUBSCRIBE TO OUR NEWSLETTER

Leave a Message
GET IN TOUCH
Copyright © 2026 TAT Electronics Co., Ltd. All Rights Reserved. | Sitemap | Privacy Policy