BMC1275-0527
TAT
BMC1275-0527
| Dimension: | |
|---|---|
| Net Weight: | |
| Rated Voltage: | |
| Operating Voltage: | |
| Rated Current: | |
| Sound Output: | |
| Resonant Frequency: | |
| Availability: | |
| Quantity: | |
Built-In Oscillator — DC Power, Instant Sound — just connect 5 V DC; no PWM code, no driver transistor, no external frequency source.
5 VDC Standard Supply — runs directly from USB, Arduino, Raspberry Pi, PLC 5 V rails; operating range 3–7 V DC.
Only 30 mA, ≥85 dB — low-current drive yet clearly audible indoor alert.
Continuous 2700 Hz Tone — steady long alarm sound ideal for fault and warning indication.
Standard Φ12 × 7.5 mm Pin Package — industry-common footprint; replaces generic 12 mm active buzzers directly.
Potted Top, Black PBT Housing — sealed against dust; through-hole pins, 7.6 mm spacing.
RoHS Compliant, -20 °C ~ +70 °C Operation.
Parameter | Specification |
|---|---|
Brand | TAT |
Model | BMC1275-0527 |
Buzzer Type | Active Electromagnetic Buzzer (built-in oscillating circuit) |
Rated Voltage | 5.0 VDC |
Operating Voltage | 3 – 7 VDC |
Rated Current | ≤ 30 mA at 5 VDC |
Sound Output (SPL) | ≥ 85 dB at 10 cm, at 5 VDC |
Resonant Frequency | 2700 ± 300 Hz |
Tone | Continuous |
Body Diameter | Φ12 ± 0.2 mm |
Body Height | 7.5 ± 0.2 mm |
Top | Potted seal, sound hole Φ2.3 mm |
Mounting | Through-hole pins; Φ0.6 ± 0.1 mm; L1 = 4.0 ± 0.5, L2 = 5.5 ± 0.5 mm; spacing 7.6 ± 0.2 mm |
Housing Material | Black PBT |
Net Weight | Approx. 1.5 g |
Operating Temperature | -20 °C ~ +70 °C |
Storage Temperature | -30 °C ~ +80 °C |
Tolerance | ±0.5 mm unless specified |
Certification | RoHS Compliant |
Origin | China |
Alarms & Doorbells — door access, wired doorbells, smoke detectors, panic buttons
Instruments & Timers — temperature controllers, timers, multimeters, scales
Industrial Control — PLC fault alarms, cabinet warning beepers
Home Appliances — microwave ovens, rice cookers, washer end-of-cycle beeps
Toys & Education — quiz buzzers, alarm kits, project boards
Smart Home — smart locks, touch switches, leak detectors
Simplest Possible Alert Solution — two wires to 5 V = sound; no firmware, no driver circuit, no design risk.
Standard 5 VDC Interface — drops into USB, Arduino and PLC designs without level conversion.
Low Power, Loud Enough — 30 mA and 85 dB balance battery use with indoor audibility.
Standard 12 mm Footprint — easy cross-reference and replacement of common active buzzers.
OEM Flexibility — intermittent/pulse tone, wider voltage and wire-lead versions available.
Q1: Active or passive? Active. It has a built-in oscillator circuit. Apply DC voltage (3–7 V) and it sounds — no PWM or external frequency needed.
Q2: How do I connect it? Connect the two pins to a 5 V DC supply (plus/minus per marking). It beeps continuously whenever power is applied — add a switch, transistor or relay to turn it on/off.
Q3: How loud is 85 dB? At 5 V measured 10 cm away, 85 dB is a clear indoor alert — typical for alarms, instruments and appliances.
Q4: Can I run it from 3.3 V or 12 V? Rated 5 V DC, operating 3–7 V DC. 3.3 V works; 12 V is outside range and may damage the unit.
Q5: Continuous or intermittent beep? Standard is continuous tone. Intermittent (pulse) versions are available on request.
Q6: Can I get wire leads instead of pins? Yes. Standard is through-hole pins; wire-lead and JST connector versions are available.