Home » News

NEWS

  • Reflow-Ready Alerts: 5 Reasons the BM5020S SMD Buzzer Wins

    2026-11-13

    Since the global electronics industry transitioned toward high-density surface-mount technology (SMT), designing compact printed circuit boards has required components that support fully automated assembly. Today, as devices shrink and production speeds accelerate, manual soldering of audio indicato Read More
  • Resonant Frequency on a Buzzer Datasheet: Why 2.7 kHz Beats 4 kHz

    2026-11-13

    A buzzer is a mechanical device before it is an electronic one. Inside the housing, a diaphragm or a ceramic disc is asked to move, and it will only move efficiently at the frequency it was tuned for. That single fact explains most of the arguments engineers have about buzzer volume, and it is the r Read More
  • 90 dB From a 1.5 V Coin Cell: Inside the BM9650E-0127-5.5

    2026-11-12

    Most audible-alert designs that must run from a coin cell end up with a boost converter in front of the buzzer. It works, but it adds a switching node, an inductor, a bill-of-materials line and a quiescent draw that keeps eating the cell while the product sits idle. The alternative is to pick a tran Read More
  • Buzzer vs Transducer: Why Your Part Clicks Instead of Tones

    2026-11-12

    The Symptom: One Click, Then NothingA new board comes back from assembly. The firmware is supposed to beep, and instead there is a single soft tick from the speaker area, then silence. The part is not dead. The driver is not necessarily broken. In the overwhelming majority of cases, the wrong member Read More
  • Protecting Buzzers from ESD and Surge: Circuit-Level Guide

    2026-11-12

    Every protection budget starts at the connector that faces the outside world and stops well short of the sounder. The USB port gets a diode array, the fieldbus gets a TVS, the antenna gets a filter, and the buzzer gets whatever general-purpose pin the firmware team had left over. That is a defensibl Read More
  • Automotive vs Industrial Buzzer: What AEC-Q200 Actually Changes

    2026-11-11

    The Same Buzzer, Two Very Different RoomsA buzzer that has run for years inside a wall-mounted control cabinet is not automatically a candidate for a dashboard. The part may be identical, the drive circuit may be identical, the tone may be identical, and yet the qualification route, the evidence pac Read More
  • How Buzzer IP Ratings Are Actually Tested (IEC 60529)

    2026-11-11

    An ingress protection claim is the easiest line on a buzzer datasheet to print and the hardest one to verify. Buyers ask for "waterproof" or "dust proof" because the field failure they are trying to prevent has a name, and a two-digit code feels like an answer. It is not an answer. It is the last li Read More
  • Buzzer SPL vs Supply Voltage: What a 12 V Part Does at 5 V

    2026-11-11

    Understanding the Baseline of Buzzer Spl Vs Supply VoltageA buzzer datasheet rarely lies. It simply answers a narrower question than the one most engineers are asking. When a page states "85 dB", it means the part produced 85 dB under one specific set of conditions — a defined drive amplitude, a def Read More
  • IEC 60601-1-8: What a Buzzer Supplier Must Hand Over

    2026-11-10

    Why Compliance Evidence Sits With the Supplier, Not the Device MakerUnder the EU Medical Device Regulation 2017/745, the legal manufacturer owns the technical documentation, the risk management file and post-market surveillance. What gets misread is where the raw material for those files comes from Read More
  • Buzzer SPL at 10 cm: What the dB Number Actually Measures

    2026-11-10

    Understanding the Baseline of Buzzer Sound Pressure Level At 10CmWhen evaluating acoustic components for electronic devices, the baseline metric that engineers rely upon is the buzzer sound pressure level at 10cm. But what exactly does this specification entail, and why is the ten-centimeter mark co Read More
  • IEC 60601-1-8 Alarm Signals: What Buzzer Suppliers Must Meet

    2026-11-10

    Every medical device programme reaches the same point: the enclosure is fixed, the board is routed, and someone from regulatory asks for evidence that the audible alarm meets IEC 60601-1-8. The question usually lands on the component supplier first, and the honest answer — that the standard does not Read More
  • Choosing a Medical Equipment Buzzer: 6 Screens Before Freeze

    2026-11-09

    A buzzer is almost always the last component added to a medical device and the first one nobody wants to change. By the time the enclosure exists and the firmware team is closing tickets, the sound source has already been squeezed into whatever footprint was left over. That is why so many projects d Read More
  • Total 4 pages  Go to Page
  • Go

WhatsApp

Call Us

+86-131-3888-7759

QUICK LINKS

PRODUCT CATEGORY

SUBSCRIBE TO OUR NEWSLETTER

Leave a Message
GET IN TOUCH
Copyright © 2026 TAT Electronics Co., Ltd. All Rights Reserved. | Sitemap | Privacy Policy