BP1440W-4801
TAT
BP1440W-4801
| Name: | |
|---|---|
| Voltage: | |
| Weight: | |
| Operating Temperature: | |
| Capacitance: | |
| Rated Current: | |
| ROHS: | |
| Availability: | |
| Quantity: | |
Ultra-Slim 4.0 mm Profile — half the thickness of standard 6–8 mm buzzers; fits thin panels and compact enclosures.
Wide Drive 1–25 Vp-p, Only 2 mA — from a 1 V battery up to 25 V industrial rails; near-zero quiescent current.
80 mm Red/Black Wire Leads — route straight to terminals; no soldering at the buzzer, no connector needed.
≥80 dB SPL at 5 Vp-p — clear indoor alert tone.
15 nF Ceramic Element — stable electro-acoustic performance, solid-state long life.
4 kHz Resonant, MCU-Programmable — sweep frequency in firmware for chimes.
Back Masking Label, Black PBT — sealed against dust; 1.2 g.
RoHS Compliant, -20 °C ~ +70 °C Operation.
Parameter | Specification |
|---|---|
Brand | TAT |
Model | BP1440W-4801 |
Buzzer Type | Passive Piezoelectric Ceramic Buzzer (external drive) |
Resonant Frequency | 4000 ± 500 Hz (tested at 4.8 kHz) |
Operating Voltage | 1 – 25 Vp-p |
Rated Current | ≤ 2 mA at 4.8 kHz, 50% duty square wave, 5 Vp-p |
Sound Output (SPL) | ≥ 80 dB at 10 cm, at 4.8 kHz 50% duty, 5 Vp-p |
Capacitance | 15000 ± 30% pF at 120 Hz |
Body Diameter | Φ14.0 ± 0.2 mm |
Body Height | 4.0 mm |
Center Hole | Φ2 mm |
Back | Masking label seal |
Lead Wire | Red(+)/Black(−), Φ0.6 ± 0.1 mm, length L1 = 80 ± 5 mm |
Housing Material | Black PBT |
Net Weight | Approx. 1.2 g |
Operating Temperature | -20 °C ~ +70 °C |
Storage Temperature | -30 °C ~ +80 °C |
Tolerance | ±0.5 mm unless specified |
Certification | RoHS Compliant |
Origin | China |
Security & Doorbells — door access, smoke detectors, wired doorbells
Instruments & Meters — temperature controllers, timers, scales
Thin Enclosures — slim panels and devices where height is constrained
Battery-Powered IoT — sensor nodes, beacons (only 2 mA)
Toys & Education — quiz buzzers, alarm kits
Industrial Panels — small status and warning beepers
4 mm Thin Where Height Is Zero — opens slim designs impossible with 6+ mm buzzers.
One Part for All Voltages — 1 to 25 Vp-p range cuts SKU count.
Wire Leads, No Soldering — 80 mm red/black leads route straight to terminals.
Micro-Power 2 mA — suits battery-powered and standby-alert designs.
OEM Flexibility — alternate frequencies, longer leads, connectors available.
Q1: Active or passive? Passive piezo. Feed a square wave at 4000 Hz (≈50% duty) from an MCU PWM pin; DC voltage alone produces no sound.
Q2: How do I drive it? Connect Red(+) to a PWM output (4 kHz square wave) and Black(−) to GND. For 12–25 Vp-p drive, use an NPN/MOSFET stage with a current-limiting resistor.
Q3: How loud is 80 dB? At 5 Vp-p measured 10 cm away, 80 dB is a clear indoor alert. Raising drive voltage toward 25 Vp-p increases SPL.
Q4: How long are the leads? Pre-attached 80 mm red(+)/black(−) leads, Φ0.6 mm. Custom lengths and connectors are available.
Q5: Can I get pins instead of leads? Yes. Standard is wire leads; pin and JST connector versions are available on request.